DISCLAIMER

All rights of photos and text reserved. Usage of photos or text from my blog on other websites or for any other purpose only with prior permission. If you want to use any material from my blog please contact me by email.

Sunday, May 25, 2014

Tube of the Month : The 1616

Hi!

Some people noticed the rather unusual rectifiers which I had in one set of the 211/211 amplifiers displayed at the recent High End fair in Munich. While the amps which were playing most of the time used 836 vacuum rectifiers, the set which was on display had the 1616 plugged in.




The 1616 is a half wave rectifier developed for transmitting applications. Half wave means it contains a single diode in the envelope. So two of them are needed for a full wave rectifier with center tapped mains transformer. Or four for a full wave bridge.

The 1616 has an UX4 base and medium metal cap for the plate connection. It has the same pinout as the 836 and 866A. Only two of the base pins are used for the filament connection. The other two are unused. It has the same filament requirement as the aforementioned two tubes: 2.5V at a hefty 5A. The latter is probably the reason why this rectifier is widely ignored by audio amplifier designers. Although it's other parameters are more than suitable for most audio power supply requirements. It can withstand a peak inverse voltage of 5kV and deliver 130mA per tube. The peak inverse voltage rating is similar to that of the 836 but only half that of the 866A. The 836 and 866A can deliver twice the current.

But since most audio amps will not get close to those limits, the 1616 is a good alternative, especially to the mercury vapour 866A. The 1616 is  vacuum rectifier which does not have the hazards of mercury spill in case of glass breakage. The 1616 has a higher voltage drop though. For initial tests of power supplies which are intended to work with the 866A the 1616 is perfect. While the 836 and 866A come in the coke bottle shape, the 1616 was made with a straight sided bulb. It has a similar impressive size than those two and while the straight sided glass seems less attractive at first glance, it has it's own kind of beauty. Since it is hardly used any more it can be found at low prices.



Pictured above is a RCA 1616 produced for the military. Hence packaged in the rather bland JAN boxes:




These have a graphite plate structure:






View from the side:





Another shot showing the graphite plate:





Metal plate versions have also been made (shown on the right):




Close up of a metal plate 1616:





The base:





Two 1616 in operation in a PSU:





Close up of one of the tubes:




The filaments are actually rather wide ribbons, as commonly used in directly heated rectifiers:




Zooming in:




A great rectifier, especially for amps which use transmitting triodes.




Best regards

Thomas



10 comments:

  1. i think i've seen 1616 in one of your early 300b amps (with 6N7).

    ReplyDelete
    Replies
    1. That's right, I used it in an early power supply which was universal and could be used for different amps.

      Delete
  2. I've noticed that the WWII Hytron 1616s have a filament that appears to have a mesh construction.

    ReplyDelete
  3. Hi, I'm curious what is the maximum size capacitor you could have connected with 2 of these in a full wave configuration? And is that the same for the 836?

    ReplyDelete
    Replies
    1. Why would you torture such a beautiful rectifier with the largest cap it can handle and get a poorly performing power supply? What a waste! If you want to find out, check the data sheet and run a simulation with PSU2 at the intended voltage.

      Delete
    2. I don't necessarily want to use the maximum size, but I would like to know what the safe range is.. I think that's generally a pretty fair thing to know when using a rectifier tube. I couldn't find that information on the datasheet. http://frank.pocnet.net/sheets/049/1/1616.pdf

      Delete
    3. The tube was intended for choke input. That's why there are no cap values. These capacitance values are anyways just a rough guideline. What really matters is the repetitive peak currents. And these depend on voltage, copper resistances and capacitances. As mentioned above you need to calculate (or simulate) this to get the cap value for your application.

      Delete
    4. It was not designed for choke input, it was designed specifically to have a high peak current for charging banks of capacitors for pulse discharge applications, thats why the peak current is so high and the average current so low.

      Delete
    5. Thanks for that info, I was not aware of that

      Delete
  4. This comment has been removed by a blog administrator.

    ReplyDelete